Alloys
G-CuSn10 |
|||
| Alloy components | |||
| Cu | 88,0-90,0 |
Fe | 0,20 |
| Sn | 9,0-11,0 |
Mn | 0,10 |
| Zn | 0,5 |
Si | 0,02 |
| Pb | 1,00 |
Sb | 0,20 |
| Al | 0,01 |
P | 0,20 |
| Ni | 2,00 |
S | 0,05 |
| Material properties | |
| Yield strength N / mm2 | 130 |
| Tensile strength N / mm2 | 250 |
| Elongation at break % | 18 |
| Brinell hardness HB 10/100 | 70 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,7 |
| Conductivity m / Ohm mm2 |
5,5-6,0 |
G-CuSn10 |
|||
|---|---|---|---|
| Features | |||
Tough, high elongation |
| Examples of use | |
Fitting and pump housing with high stress, control, running and paddle wheels for pumps and water turbines |
G-CuSn12 |
|||
| Alloy components | |||
| Cu | 85,0-88,5 |
Fe | 0,20 |
| Sn | 11,0-13,0 |
Mn | 0,20 |
| Zn | 0,5 |
Si | 0,01-0,02 |
| Pb | 0,70 |
Sb | 0,15 |
| Al | 0,01 |
P | 0,60 |
| Ni | 2,00 |
S | 0,05 |
| Material properties | |
| Yield strength N / mm2 | 140 |
| Tensile strength N / mm2 | 260 |
| Elongation at break % | 7 |
| Brinell hardness HB 10/100 | 80 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,6 |
| Conductivity m / Ohm mm2 |
5,0-5,5 |
G-CuSn12 |
|||
|---|---|---|---|
| Features | |||
Tough and hard, good wear resistance |
G-CuSn12 |
|||
|---|---|---|---|
| Features | |||
Tough and hard, good wear resistance |
G-CuSn12Ni |
|||
| Alloy components | |||
| Cu | 84,5-87,5 |
Fe | 0,20 |
| Sn | 11,0-13,0 |
Mn | 0,20 |
| Zn | 0,4 |
Si | 0,01 |
| Pb | 0,30 |
Sb | 0,10 |
| Al | 0,01 |
P | 0,05-0,4 |
| Ni | 1,5-2,5 |
S | 0,05 |
| Material properties | |
| Yield strength N / mm2 | 160 |
| Tensile strength N / mm2 | 280 |
| Elongation at break % | 12 |
| Brinell hardness HB 10/100 | 85 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,6 |
| Conductivity m / Ohm mm2 |
5,0-5,5 |
G-CuSn12Ni |
|||
|---|---|---|---|
| Features | |||
Hard |
| Examples of use | |
| Bearing shells with load peaks to 6000 N / cm, heavy-duty slide plates and wear strips. |
G-CuSn14 |
|||
| Alloy components | |||
| Cu | 85,0-87,0 |
Fe | 0,20 |
| Sn | 13,0-15,0 |
Mn | 0 |
| Zn | 0,5 |
Si | 0 |
| Pb | 1,00 |
Sb | 0,25 |
| Al | 0 |
P | 0,20 |
| Ni | 1,0 |
S | 0,05 |
| Material properties | |
| Yield strength N / mm2 | 150 |
| Tensile strength N / mm2 | 250 |
| Elongation at break % | 5 |
| Brinell hardness HB 10/100 | 90 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,5 |
| Conductivity m / Ohm mm2 |
4,7-5,0 |
G-CuSn14 |
|||
|---|---|---|---|
| Features | |||
Well castable |
| Examples of use | |
| Fittings for water and steam up to 225 ° C, normally stressed pump housing; thin-walled intricate castings, C + Z to normally stressed wear and valve seat rings, moderately stressed plain bearings. |
CuSn5Zn5Pb |
|||
| Alloy components | |||
| Cu | 83,0-87,0 |
Fe | 0,30 |
| Sn | 4,0-6,0 |
Mn | 0 |
| Zn | 4,0-6,0 |
Si | 0,01 |
| Pb | 3,00 |
Sb | 0,10 |
| Al | 0,01 |
P | 0,04 |
| Ni | 0,60 |
S | 0,04 |
| Material properties | |
| Yield strength N / mm2 | |
| Tensile strength N / mm2 | |
| Elongation at break % | |
| Brinell hardness HB 10/100 | |
Shrinkage rule S % approximately |
|
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
|
| Conductivity m / Ohm mm2 |
|
CuSn5Zn5Pb |
|||
|---|---|---|---|
| Features | |||
| according to Drinking Water Regulations DIN 50930 Part 6 |
| Examples of use | |
| Fittings and pumps in the drinking water area |
G-CuSn5ZnPb |
|||
| Alloy components | |||
| Cu | 83,0-87,0 |
Fe | 0,30 |
| Sn | 4,0-6,0 |
Mn | 0 |
| Zn | 4,0-6,0 |
Si | 0,01 |
| Pb | 4,0-6,0 |
Sb | 0,25 |
| Al | 0,01 |
P | 0,10 |
| Ni | 2,00 |
S | 0,10 |
| Material properties | |
| Yield strength N / mm2 | 90 |
| Tensile strength N / mm2 | 200 |
| Elongation at break % | 13 |
| Brinell hardness HB 10/100 | 60 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,7 |
| Conductivity m / Ohm mm2 |
8,0 |
G-CuSn5ZnPb |
|||
|---|---|---|---|
| Features | |||
| Medium hard, running properties |
| Examples of use | |
| Bearing shells and bushings also for piston pins for peak loads up to 4000 N / cm², also when subjected to slight edge pressure, C + Z also crank bearing and toggle bearing for peak loads up to 3000 N / cm², propeller shaft covers, threaded inserts and packing glands, moderately stressed. Coupling pieces, friction discs until highly stressed. Wear strips and support rails for machine tools. |
G-CuSn7ZnPb |
|||
| Alloy components | |||
| Cu | 81,0-85,0 |
Fe | 0,20 |
| Sn | 6,0-8,0 |
Mn | 0 |
| Zn | 2,0-5,0 |
Si | 0,01 |
| Pb | 5,0-8,0 |
Sb | 0,30 |
| Al | 0,01 |
P | 0,10 |
| Ni | 2,00 |
S | 0,10 |
| Material properties | |
| Yield strength N / mm2 | 120 |
| Tensile strength N / mm2 | 230 |
| Elongation at break % | 15 |
| Brinell hardness HB 10/100 | 60 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,8 |
| Conductivity m / Ohm mm2 |
|
Hard
| Examples of use | |
| Sliding bearing shells, worm gears with low sliding speed. Moderately stressed sliding and coupling pieces, stern tubes. C + Z also propeller shaft covers, covers for paper and calender rolls, moderately stressed spindle nuts. |
G-CuSn10Zn |
|||
| Alloy components | |||
| Cu | 86,0-89,0 |
Fe | 0,25 |
| Sn | 9,0-11,0 |
Mn | 0 |
| Zn | 1,0-3,0 |
Si | 0 |
| Pb | 1,50 |
Sb | 0,30 |
| Al | 0 |
P | 0,05 |
| Ni | 2,00 |
S | 0,10 |
| Material properties | |
| Yield strength N / mm2 | 130 |
| Tensile strength N / mm2 | 260 |
| Elongation at break % | 15 |
| Brinell hardness HB 10/100 | 75 |
Shrinkage rule S % approximately |
1,2-1,8 |
| Shrinkage rule K % approximately | |
| Density kg / dm3 |
8,7 |
| Conductivity m / Ohm mm2 |
6,0 |
G-CuAl9 |
|||
| Alloy components | |||
| Cu | 88,0-92,0 |
Fe | 1,20 |
| Sn | 0,30 |
Mn | 0,50 |
| Zn | 0,50 |
Si | 0,20 |
| Pb | 0,30 |
Sb | 0 |
| Al | 8,0-10,5 |
P | 0 |
| Ni | 1,00 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 150 |
| Tensile strength N / mm2 | 400 |
| Elongation at break % | 15 |
| Brinell hardness HB 10/100 | 80 |
Shrinkage rule S % approximately |
1,8-2,2 |
| Shrinkage rule K % approximately | 1,4-1,8 |
| Density kg / dm3 |
7,6 |
| Conductivity m / Ohm mm2 |
9,5 |
G-CuAl9 |
|||
|---|---|---|---|
| Features | |||
S, and K |
| Examples of use | |
| Fittings and castings for the chemical and food industries. |
G-CuAl10Fe |
|||
| Alloy components | |||
| Cu | 83,0-89,5 |
Fe | 2,0-4,0 |
| Sn | 0,30 |
Mn | 1,00 |
| Zn | 0,50 |
Si | 0,20 |
| Pb | 0,20 |
Sb | 0 |
| Al | 8,5-11,0 |
P | 0 |
| Ni | 3,00 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 180 |
| Tensile strength N / mm2 | 500 |
| Elongation at break % | 15 |
| Brinell hardness HB 10/100 | 115 |
Shrinkage rule S % approximately |
1,8-2,2 |
| Shrinkage rule K % approximately | 1,4-1,8 |
| Density kg / dm3 |
7,5 |
| Conductivity m / Ohm mm2 |
3,5-4,0 |
G-CuAl10Fe |
|||
|---|---|---|---|
| Features | |||
| Strength values only slightly dependent on temperature between ± 200 ° C |
| Examples of use | |
| Construction material, levers, housings, connectors, fittings, sprockets, bevel gears, synchroniser rings, switching segments and forks for textile machinery and vehicles. Carbon holder in electrical engineering. |
G-CuAl10Ni |
|||
| Alloy components | |||
| Cu | 76,0-83,0 |
Fe | 4,0-5,5 |
| Sn | 0,10 |
Mn | 3,00 |
| Zn | 0,50 |
Si | 0,10 |
| Pb | 0,03 |
Sb | 0 |
| Al | 8,5-10,5 |
P | 0 |
| Ni | 4,0-6,0 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 250 |
| Tensile strength N / mm2 | 600 |
| Elongation at break % | 13 |
| Brinell hardness HB 10/100 | 140 |
Shrinkage rule S % approximately |
1,8-2,2 |
| Shrinkage rule K % approximately | 1,4-1,8 |
| Density kg / dm3 |
7,6 |
| Conductivity m / Ohm mm2 |
2,5 |
G-CuAl10Ni |
|||
|---|---|---|---|
| Features | |||
| Resistant even in hot sea water |
| Examples of use | |
| Superheated steam fittings, propellers, stern tubes, distributor heads and reverse bends in apparatus construction and petrochemicals. Running wheels, pump housing, C and Z: Bearings with high impact loads, worm and helical gears, thrust nuts and other wear-stressed parts, all with good lubrication. |
G-CuAl11Ni |
|||
| Alloy components | |||
| Cu | 72,0-78,0 |
Fe | 4,0-7,0 |
| Sn | 0,20 |
Mn | 2,50 |
| Zn | 0,50 |
Si | 0,10 |
| Pb | 0,05 |
Sb | 0 |
| Al | 10,0-12,0 |
P | 0 |
| Ni | 4,0-7,5 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 320 |
| Tensile strength N / mm2 | 680 |
| Elongation at break % | 5 |
| Brinell hardness HB 10/100 | 170 |
Shrinkage rule S % approximately |
1,8-2,2 |
| Shrinkage rule K % approximately | 1,4-1,8 |
| Density kg / dm3 |
|
| Conductivity m / Ohm mm2 |
|
G-CuAl11Ni |
|||
|---|---|---|---|
| Features | |||
| High strength properties |
| Examples of use | |
| Cavitation-resistant, very high resistance (good lubrication required), like CC333G (G-CuAl10Ni), but with higher requirements. |
G-CuPb5Sn |
|||
| Alloy components | |||
| Cu | 84,0-87,0 |
Fe | 0,25 |
| Sn | 9,0-11,0 |
Mn | 0 |
| Zn | 1,00 |
Si | 0 |
| Pb | 4,0-6,0 |
Sb | 0,35 |
| Al | 0 |
P | 0,05 |
| Ni | 1,50 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 130 |
| Tensile strength N / mm2 | 240 |
| Elongation at break % | 15 |
| Brinell hardness HB 10/100 | 70 |
Shrinkage rule S % approximately |
1,4 |
| Shrinkage rule K % approximately | 1,4 |
| Density kg / dm3 |
8,7 |
| Conductivity m / Ohm mm2 |
6,5 |
G-CuPb5Sn |
|||
|---|---|---|---|
| Features | |||
| Resistant to diluted hydrochloric, sulfuric and fatty acids |
| Examples of use | |
| Fittings, bearings |
G-CuPb10Sn |
|||
| Alloy components | |||
| Cu | 78,0-82,0 |
Fe | 0,25 |
| Sn | 9,0-11,0 |
Mn | 0,20 |
| Zn | 2,00 |
Si | 0,01 |
| Pb | 8,0-11,0 |
Sb | 0,50 |
| Al | 0,01 |
P | 0,10 |
| Ni | 2,00 |
S | 0,10 |
| Material properties | |
| Yield strength N / mm2 | 80 |
| Tensile strength N / mm2 | 180 |
| Elongation at break % | 8 |
| Brinell hardness HB 10/100 | 60 |
Shrinkage rule S % approximately |
1,4 |
| Shrinkage rule K % approximately | 1,4 |
| Density kg / dm3 |
9,0 |
| Conductivity m / Ohm mm2 |
6,0 |
G-CuPb10Sn |
|||
|---|---|---|---|
| Features | |||
| Better running properties than CuSN bronze and red bronze |
| Examples of use | |
| Bearings with peak loads up to 6000 N / cm² with good lubrication. In composite bearings such as piston pins and gear bushings to 10000 N / cm²; also when subject to edge pressure such as calender rolls, bearings for cars and hot rolling mills. |
G-CuZn15Si4 |
|||
| Alloy components | |||
| Cu | 78,0-83,0 |
Fe | 0,60 |
| Sn | 0,30 |
Mn | 0,20 |
| Zn | Rest |
Si | 3,0-5,0 |
| Pb | 0,80 |
Sb | 0,05 |
| Al | 0,10 |
P | 0,03 |
| Ni | 1,00 |
S | 0,10 |
| Material properties | |
| Yield strength N / mm2 | 230 |
| Tensile strength N / mm2 | 400 |
| Elongation at break % | 10 |
| Brinell hardness HB 10/100 | 100 |
Shrinkage rule S % approximately |
1,4 |
| Shrinkage rule K % approximately | 1,0-1,4 |
| Density kg / dm3 |
8,1-8,6 |
| Conductivity m / Ohm mm2 |
3,0-6,0 |
G-CuZn15Si4 |
|||
|---|---|---|---|
| Features | |||
| Higher strength, hardness and wear resistance |
| Examples of use | |
| Highly stressed, thin-walled and intricate parts for mechanical engineering, apparatus construction and ship building, Electrical and Precision Engineering, e.g. high pressure die casting bearings, gravity die casting, instead of steel parts, pumps and fittings, also for high pressure, gear wheels and worm gears, sprockets. |
G-CuZn35Al1 |
|||
| Alloy components | |||
| Cu | 57,0-65,0 |
Fe | 0,5-2,0 |
| Sn | 1,00 |
Mn | 0,5-3,0 |
| Zn | Rest |
Si | 0,10 |
| Pb | 0,50 |
Sb | 0,08 |
| Al | 0,5-2,5 |
P | 0,03 |
| Ni | 6,00 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 170 |
| Tensile strength N / mm2 | 450 |
| Elongation at break % | 20 |
| Brinell hardness HB 10/100 | 110 |
Shrinkage rule S % approximately |
1,8-2,0 |
| Shrinkage rule K % approximately | 0,8-1,5 |
| Density kg / dm3 |
8,6 |
| Conductivity m / Ohm mm2 |
8,0 |
G-CuZn35Al1 |
|||
|---|---|---|---|
| Features | |||
| Sand and gravity die casting |
| Examples of use | |
| Moderate sliding properties, pressure nuts for rolling mills and screw presses, primary and packing glands, propellers, machine components. |
GD-CuZn37Pb |
|||
| Alloy components | |||
| Cu | 59,0-63,0 |
Fe | 0,50 |
| Sn | 0,70 |
Mn | 0,10 |
| Zn | Rest |
Si | 0,10 |
| Pb | 0,5-2,5 |
Sb | 0 |
| Al | 0,2-0,8 |
P | 0,05 |
| Ni | 1,00 |
S | 0 |
| Material properties | |
| Yield strength N / mm2 | 120 |
| Tensile strength N / mm2 | 280 |
| Elongation at break % | 4 |
| Brinell hardness HB 10/100 | 75 |
Shrinkage rule S % approximately |
1,5-1,7 |
| Shrinkage rule K % approximately | 0,8-1,2 |
| Density kg / dm3 |
8,5 |
| Conductivity m / Ohm mm2 |
11,0 |
GD-CuZn37Pb |
|||
|---|---|---|---|
| Features | |||
| Gravity die casting, die casting (including sand in wet sand) |
| Examples of use | |
Represented are the alloy components of silicon (Si), iron (Fe), copper (Cu), manganese (Mn), nickel (Ni), lead (Pb), tin (Sn), antimony (Sb), aluminium (Al), phosphorus (P), sulphur (S), zinc (Zn); as well as some material properties: yield strength, tensile strength, elongation at break, Brinell hardness, shrinkage in sand casting and gravity die casting, density and electrical conductivity.
In another view, of possible uses and examples as well as other properties are shown.